API Functions module for L2CAP. More...

Functions
wiced_bool_t	wiced_bt_l2cap_register_fixed_channel (uint16_t fixed_cid, wiced_bt_l2cap_fixed_chnl_reg_t *p_freg)
	Register a fixed channel. More...

wiced_bool_t	wiced_bt_l2cap_deregister_fixed_channel (uint16_t fixed_cid)
	De-register a fixed channel. More...

wiced_bool_t	wiced_bt_l2cap_connect_fixed_chnl (uint16_t fixed_cid, wiced_bt_device_address_t bd_addr, wiced_bt_ble_address_type_t ble_addr_type)
	Connect an fixed signalling channel to a remote device. More...

uint16_t	wiced_bt_l2cap_send_fixed_chnl_data (uint16_t fixed_cid, wiced_bt_device_address_t rem_bda, uint8_t *p_data, uint16_t data_len)
	Write data on a fixed signalling channel. More...

wiced_bool_t	wiced_bt_l2cap_remove_fixed_chnl (uint16_t fixed_cid, wiced_bt_device_address_t rem_bda)
	Remove a fixed channel to a remote device. More...

wiced_bool_t	wiced_bt_l2cap_set_fixed_channel_timeout (wiced_bt_device_address_t rem_bda, uint16_t fixed_cid, uint16_t idle_timeout)
	Higher layers call this function to set the idle timeout for a fixed channel. More...

wiced_bool_t	wiced_bt_l2cap_ecrb_register (uint16_t psm, wiced_bt_l2cap_ecrb_cb_ptrs_t *p_ecrb_callbacks)
	Application calls this function to register support for enhanced credit-based channels. More...

wiced_bool_t	wiced_bt_l2cap_ecrb_deregister (uint16_t psm)
	Application calls this function to deregister support for enhanced credit-based channels. More...

int	wiced_bt_l2cap_ecrb_connect_req (uint16_t psm, wiced_bt_transport_t transport, wiced_bt_device_address_t bd_addr, wiced_bt_ble_address_type_t bd_addr_type, wiced_bt_ble_conn_mode_t conn_mode, uint16_t our_rx_mtu, uint16_t our_rx_mps, int num_channels, tDRB **p_rx_drb_list, wiced_bt_ecrb_cid_list_t lcid_list)
	Higher layers call this function to create up to 5 credit-based L2CAP connections on the same PSM. More...

void	wiced_bt_l2cap_ecrb_ConnectRsp (uint16_t result, uint8_t trans_id, int16_t our_rx_mtu, uint16_t our_rx_mps, wiced_bt_ecrb_cid_list_t lcid_list, tDRB **p_rx_drb_list)
	Higher layers call this function to accept incoming Enhanced Credit-based L2CAP channel establishment, for which they had gotten a connect indication callback. More...

wiced_bool_t	wiced_bt_l2cap_ecrb_reconfigure (uint16_t new_rx_mtu, int16_t new_rx_mps, int num_channels, wiced_bt_ecrb_cid_list_t lcid_list, tDRB **p_rx_drb_list)
	Higher layers call this function to reconfigure the MTU and or MPS of Enhanced Credit-based L2CAP channels. More...

wiced_bool_t	wiced_bt_l2cap_get_current_config (uint16_t lcid, wiced_bt_l2cap_cfg_information_t *pp_our_cfg, wiced_bt_l2cap_ch_cfg_bits_t p_our_cfg_bits, wiced_bt_l2cap_cfg_information_t *pp_peer_cfg, wiced_bt_l2cap_ch_cfg_bits_t p_peer_cfg_bits)
	This function returns configurations of L2CAP channel. More...

uint16_t	wiced_bt_l2cap_register (uint16_t psm, wiced_bt_l2cap_appl_information_t *p_cb_information)
	Other layers call this function to register for L2CAP services. More...

void	wiced_bt_l2cap_deregister (uint16_t psm)
	Other layers call this function to deregister for L2CAP services. More...

uint16_t	wiced_bt_l2cap_allocate_psm (void)
	Other layers call this function to find an unused PSM for L2CAP services. More...

wiced_bool_t	wiced_bt_l2cap_disconnect_req (uint16_t cid)
	Higher layers call this function to disconnect a channel. More...

wiced_bool_t	wiced_bt_l2cap_disconnect_rsp (uint16_t cid)
	Higher layers call this function to acknowledge the disconnection of a channel. More...

uint8_t	wiced_bt_l2cap_data_write (uint16_t cid, uint8_t *p_buf, uint16_t buf_len, uint16_t flags)
	Higher layers call this function to write data with extended. More...

wiced_bool_t	wiced_bt_l2cap_set_idle_timeout (uint16_t cid, uint16_t timeout, wiced_bool_t is_global)
	Higher layers call this function to set the idle timeout for a connection, or for all future connections. More...

wiced_bool_t	wiced_bt_l2cap_set_idle_timeout_by_bd_addr (wiced_bt_device_address_t bd_addr, uint16_t timeout, wiced_bt_transport_t transport)
	Higher layers call this function to set the idle timeout for a connection. More...

wiced_bool_t	wiced_bt_l2cap_get_bdaddrby_handle (uint16_t handle, wiced_bt_device_address_t bd_addr)
	Get BD address for the given HCI handle. More...

wiced_bool_t	wiced_bt_l2cap_cancel_ble_connect_req (wiced_bt_device_address_t rem_bda)
	Cancel a pending connection attempt to a LE device. More...

wiced_bool_t	wiced_bt_l2cap_update_ble_conn_params (wiced_bt_device_address_t rem_bdRa, uint16_t min_int, uint16_t max_int, uint16_t latency, uint16_t timeout)
	Update LE connection parameters. More...

wiced_bool_t	wiced_bt_l2cap_enable_update_ble_conn_params (wiced_bt_device_address_t rem_bda, wiced_bool_t enable)
	Enable or disable updating LE connection params based on the request from the peer. More...

uint8_t	wiced_bt_l2cap_get_ble_conn_role (wiced_bt_device_address_t bd_addr)
	This function returns the connection role. More...

uint16_t	wiced_bt_l2cap_le_register (uint16_t le_psm, wiced_bt_l2cap_le_appl_information_t *p_cb_information)
	Other layers call this function to register L2CAP services for LE_PSM. More...

wiced_bool_t	wiced_bt_l2cap_le_deregister (uint16_t le_psm)
	Other layers call this function to deregister L2CAP services for LE_PSM. More...

uint16_t	wiced_bt_l2cap_le_connect_req (uint16_t le_psm, wiced_bt_device_address_t p_bd_addr, wiced_bt_ble_address_type_t bd_addr_type, wiced_bt_ble_conn_mode_t conn_mode, uint16_t rx_mtu, uint8_t req_security, uint8_t req_encr_key_size, tDRB *p_rx_drb)
	Higher layers call this function to create an L2CAP connection for LE_PSM. More...

wiced_bool_t	wiced_bt_l2cap_le_connect_rsp (wiced_bt_device_address_t p_bd_addr, uint8_t id, uint16_t lcid, uint16_t result, uint16_t rx_mtu, tDRB *p_rx_drb)
	Higher layers call this function to accept an incoming LE L2CAP connection, for which they had gotten an connect indication callback. More...

wiced_bool_t	wiced_bt_l2cap_le_disconnect_req (uint16_t lcid)
	Higher layers call this function to disconnect a LE COC channel. More...

wiced_bool_t	wiced_bt_l2cap_le_disconnect_rsp (uint16_t lcid)
	Higher layers call this function to acknowledge the disconnection of a LE COC channel. More...

uint8_t	wiced_bt_l2cap_le_data_write (uint16_t cid, uint8_t *p_data, uint16_t buf_len)
	Send data over LE connection-oriented channel. More...

wiced_bool_t	wiced_bt_l2cap_le_set_user_congestion (uint16_t lcid, wiced_bool_t flow_off_peer)
	App can call this function to flow control data reception from the peer (flow controlled channels only, viz LE COC, ECRB channels) To stop sending credits/flow off the remote peer set `flow_off_peer` to WICED_TRUE To resume sending credits/flow on set `flow_off_peer` to WICED_FALSE. More...

uint16_t	wiced_bt_l2cap_le_get_peer_mtu (uint16_t lcid)
	Higher layers call this function to get peer MTU. More...

uint16_t	wiced_bt_l2cap_le_determ_secur_rsp (wiced_bt_device_address_t bd_addr, uint8_t req_secur, uint8_t req_encr_key_size)
	Higher layers call this function to check if the current device security settings are sufficient to continue with call establishment. More...

Detailed Description

API Functions module for L2CAP.

Function Documentation

uint16_t wiced_bt_l2cap_allocate_psm ( void )

Other layers call this function to find an unused PSM for L2CAP services.

Returns: PSM to use.

wiced_bool_t wiced_bt_l2cap_cancel_ble_connect_req ( wiced_bt_device_address_t rem_bda )

Cancel a pending connection attempt to a LE device.

Parameters

[in] rem_bda : BD Address of remote

Returns: : TRUE if connection was cancelled

wiced_bool_t wiced_bt_l2cap_connect_fixed_chnl	(	uint16_t	fixed_cid,
		wiced_bt_device_address_t	bd_addr,
		wiced_bt_ble_address_type_t	ble_addr_type
	)

Connect an fixed signalling channel to a remote device.

Parameters

[in]	fixed_cid	: Fixed CID
[in]	bd_addr	: BD Address of remote
[in]	ble_addr_type	: Address type

Returns: TRUE if connection started

uint8_t wiced_bt_l2cap_data_write	(	uint16_t	cid,
		uint8_t *	p_buf,
		uint16_t	buf_len,
		uint16_t	flags
	)

Higher layers call this function to write data with extended.

Parameters

[in]	cid	: CID value
[in]	p_buf	: Input buffer
[in]	buf_len	: p_buf buffer size
[in]	flags	: refer L2CAP data write flags

Returns: refer L2CAP data write result

void wiced_bt_l2cap_deregister ( uint16_t psm )

Other layers call this function to deregister for L2CAP services.

Parameters

[in] psm : PSM value

Returns: void

wiced_bool_t wiced_bt_l2cap_deregister_fixed_channel ( uint16_t fixed_cid )

De-register a fixed channel.

Parameters

[in] fixed_cid : Fixed Channel #

Returns: TRUE if registered OK

wiced_bool_t wiced_bt_l2cap_disconnect_req ( uint16_t cid )

Higher layers call this function to disconnect a channel.

Parameters

[in] cid : CID value

Returns: TRUE if disconnect sent, else FALSE

wiced_bool_t wiced_bt_l2cap_disconnect_rsp ( uint16_t cid )

Higher layers call this function to acknowledge the disconnection of a channel.

Parameters

[in] cid : CID value

Returns: void

int wiced_bt_l2cap_ecrb_connect_req	(	uint16_t	psm,
		wiced_bt_transport_t	transport,
		wiced_bt_device_address_t	bd_addr,
		wiced_bt_ble_address_type_t	bd_addr_type,
		wiced_bt_ble_conn_mode_t	conn_mode,
		uint16_t	our_rx_mtu,
		uint16_t	our_rx_mps,
		int	num_channels,
		tDRB **	p_rx_drb_list,
		wiced_bt_ecrb_cid_list_t	lcid_list
	)

Higher layers call this function to create up to 5 credit-based L2CAP connections on the same PSM.

Note: The connection is not established at this time, but connection establishment gets started. The callback function will be invoked when connection establishes or fails.

Parameters

[in]	psm	PSM Value
[in]	transport	BT transport for the connection
[in]	bd_addr	: Bluetooth device address to connect
[in]	bd_addr_type	BLE_ADDR_PUBLIC or BLE_ADDR_RANDOM
[in]	conn_mode	: LE connection mode
[in]	our_rx_mtu	Our RX MTU to be used for the channels
[in]	our_rx_mps	Our RX MPS to be used for the channels

Note: our_rx_mps must be less then wiced_bt_cfg_ble_t::ble_max_rx_pdu_size or wiced_bt_cfg_br_t::br_max_rx_pdu_size for LE and BR/EDR transports respectively

Parameters

[in]	num_channels	: Number of channels to be created
[in]	p_rx_drb_list	list of the allocated tDRB 's, one for each `num_channels`

Note: : the size of DRB allocated must be >= our_rx_mtu

Parameters

[out] lcid_list list of cids (channel ids) which will be started

Returns: number of channels which will be started

void wiced_bt_l2cap_ecrb_ConnectRsp	(	uint16_t	result,
		uint8_t	trans_id,
		int16_t	our_rx_mtu,
		uint16_t	our_rx_mps,
		wiced_bt_ecrb_cid_list_t	lcid_list,
		tDRB **	p_rx_drb_list
	)

Higher layers call this function to accept incoming Enhanced Credit-based L2CAP channel establishment, for which they had gotten a connect indication callback.

Parameters

[in]	result	: Result of the connection set by the application. L2CAP result codes (L2CAP_CONN_RESULT)
[in]	trans_id	: trans_id received in the wiced_bt_l2cap_ecrb_connect_ind
[in]	our_rx_mtu	Our RX MTU to be used for the channels
[in]	our_rx_mps	Our RX MPS to be used for the channels

Note: our_rx_mps must be less then wiced_bt_cfg_ble_t::ble_max_rx_pdu_size or wiced_bt_cfg_br_t::br_max_rx_pdu_size for LE and BR/EDR transports respectively

Parameters

[out] lcid_list list of cids (channel ids) which will be started as received in wiced_bt_l2cap_ecrb_connect_ind

Note: The CID list in lcid_list must match the CID list returned in the callback. The DRB pointer list must contain a valid DRB pointer for each non-zero CID in the list that the application accepts.

Parameters

[in] p_rx_drb_list : list of the allocated tDRB 's, one for each num_channels

Note: : the size of DRB allocated must be >= our_rx_mtu

Returns: void

wiced_bool_t wiced_bt_l2cap_ecrb_deregister ( uint16_t psm )

Application calls this function to deregister support for enhanced credit-based channels.

The PSM must have been previously registered.

Parameters

[in] psm PSM value

Returns: WICED_TRUE if all OK.

wiced_bool_t wiced_bt_l2cap_ecrb_reconfigure	(	uint16_t	new_rx_mtu,
		int16_t	new_rx_mps,
		int	num_channels,
		wiced_bt_ecrb_cid_list_t	lcid_list,
		tDRB **	p_rx_drb_list
	)

Higher layers call this function to reconfigure the MTU and or MPS of Enhanced Credit-based L2CAP channels.

Parameters

[in] new_rx_mtu Our new RX MTU to be used for the channels

Note: If new_rx_mtu is zero, no change to MTU is requested. Otherwise new_rx_mtu must be larger than the old MTU for all channels.

Parameters

[in] new_rx_mps Our new RX MPS to be used for the channels

Note: If new_rx_mts is zero, no change to MPS is requested. Otherwise new_rx_mps must be larger than the old MPS for all channels.; new_rx_mps must be less then wiced_bt_cfg_ble_t::ble_max_rx_pdu_size or wiced_bt_cfg_br_t::br_max_rx_pdu_size for LE and BR/EDR transports respectively

Parameters

[in]	num_channels	: Number of channels to be created
[in]	lcid_list	: list of channels to be reconfigured
[in]	p_rx_drb_list	: list of the allocated tDRB 's, one for each `num_channels`

Note: : the size of DRB allocated must be >= new_rx_mtu

Returns: WICED_TRUE if reconfigure sent OK

wiced_bool_t wiced_bt_l2cap_ecrb_register	(	uint16_t	psm,
		wiced_bt_l2cap_ecrb_cb_ptrs_t *	p_ecrb_callbacks
	)

Application calls this function to register support for enhanced credit-based channels.

The PSM must have been previously registered for BR and/or LE.

Parameters

[in]	psm	: PSM value
[in]	p_ecrb_callbacks	: callbacks for the credit based channel connections

Returns: WICED_TRUE if all ok

wiced_bool_t wiced_bt_l2cap_enable_update_ble_conn_params	(	wiced_bt_device_address_t	rem_bda,
		wiced_bool_t	enable
	)

Enable or disable updating LE connection params based on the request from the peer.

Parameters

[in]	rem_bda	Remote Bd Address
[in]	enable	TRUE to enable,FALSE to disable.

Returns: : TRUE if update started

wiced_bool_t wiced_bt_l2cap_get_bdaddrby_handle	(	uint16_t	handle,
		wiced_bt_device_address_t	bd_addr
	)

Get BD address for the given HCI handle.

Parameters

[in]	handle	: HCI handle
[in]	bd_addr	: Peer Bd Address

Returns: : TRUE if found lcb for the given handle, FALSE otherwise

uint8_t wiced_bt_l2cap_get_ble_conn_role ( wiced_bt_device_address_t bd_addr )

This function returns the connection role.

Parameters

[in] bd_addr BD Address

Returns: link role.( 0 => HCI_ROLE_CENTRAL and 1 => HCI_ROLE_PERIPHERAL)

wiced_bool_t wiced_bt_l2cap_get_current_config	(	uint16_t	lcid,
		wiced_bt_l2cap_cfg_information_t **	pp_our_cfg,
		wiced_bt_l2cap_ch_cfg_bits_t *	p_our_cfg_bits,
		wiced_bt_l2cap_cfg_information_t **	pp_peer_cfg,
		wiced_bt_l2cap_ch_cfg_bits_t *	p_peer_cfg_bits
	)

This function returns configurations of L2CAP channel.

Parameters

[in]	lcid	: Local CID
[in]	pp_our_cfg	: pointer of our saved configuration options
[in]	p_our_cfg_bits	: valid config in bitmap
[in]	pp_peer_cfg	: pointer of peer's saved configuration options
[in]	p_peer_cfg_bits	: valid config in bitmap

Returns: TRUE if successful

uint16_t wiced_bt_l2cap_le_connect_req	(	uint16_t	le_psm,
		wiced_bt_device_address_t	p_bd_addr,
		wiced_bt_ble_address_type_t	bd_addr_type,
		wiced_bt_ble_conn_mode_t	conn_mode,
		uint16_t	rx_mtu,
		uint8_t	req_security,
		uint8_t	req_encr_key_size,
		tDRB *	p_rx_drb
	)

Higher layers call this function to create an L2CAP connection for LE_PSM.

Note that the connection is not established at this time, but connection establishment gets started. The callback function will be invoked when connection establishes or fails.

Parameters

[in]	le_psm	: LE PSM value
[in]	p_bd_addr	: BD Address
[in]	bd_addr_type	: BLE_ADDR_PUBLIC or BLE_ADDR_RANDOM
[in]	conn_mode	: BLE_CONN_MODE_HIGH_DUTY or BLE_CONN_MODE_LOW_DUTY
[in]	rx_mtu	: Rx MTU value

Note: rx_mtu must be less then wiced_bt_cfg_ble_t::ble_max_rx_pdu_size

Parameters

[in]	req_security	: Security required
[in]	req_encr_key_size	: key size
[in]	p_rx_drb	: DRB to receive peer's data. MUST be large enough to hold RX MTU data, check tDRB

Note: p_rx_drb can be released by the application on receiving a callback with the wiced_bt_l2cap_le_appl_information_t::le_release_drb_cb of the p_cb_information member of wiced_bt_l2cap_le_register

Returns: the CID of the connection, or 0 if it failed to start

wiced_bool_t wiced_bt_l2cap_le_connect_rsp	(	wiced_bt_device_address_t	p_bd_addr,
		uint8_t	id,
		uint16_t	lcid,
		uint16_t	result,
		uint16_t	rx_mtu,
		tDRB *	p_rx_drb
	)

Higher layers call this function to accept an incoming LE L2CAP connection, for which they had gotten an connect indication callback.

Parameters

[in]	p_bd_addr	: BD Address
[in]	id	: ID received from wiced_bt_l2cap_le_connect_indication_cback_t callback.
[in]	lcid	: Local CID
[in]	result	: L2CAP result codes (L2CAP_CONN_RESULT)
[in]	rx_mtu	: Rx MTU value (must be <= ACL_POOL_SIZE)
[in]	p_rx_drb	: DRB to receive peer's data. MUST be large enough to hold RX MTU data, check tDRB

Note: p_rx_drb can be released by the application on receiving a callback with the wiced_bt_l2cap_le_appl_information_t::le_release_drb_cb of the p_cb_information member of wiced_bt_l2cap_le_register

Returns: TRUE for success, FALSE for failure

uint8_t wiced_bt_l2cap_le_data_write	(	uint16_t	cid,
		uint8_t *	p_data,
		uint16_t	buf_len
	)

Send data over LE connection-oriented channel.

Parameters

[in]	cid	: CID value
[in]	p_data	: Input buffer
[in]	buf_len	: p_data buffer size

Returns: L2CAP_DATAWRITE_SUCCESS, if data accepted, else FALSE L2CAP_DATAWRITE_CONGESTED, if data accepted and the channel is congested L2CAP_DATAWRITE_FAILED, if error

wiced_bool_t wiced_bt_l2cap_le_deregister ( uint16_t le_psm )

Other layers call this function to deregister L2CAP services for LE_PSM.

Parameters

[in] le_psm LE PSM value

Returns: TRUE for success, FALSE for failure

uint16_t wiced_bt_l2cap_le_determ_secur_rsp	(	wiced_bt_device_address_t	bd_addr,
		uint8_t	req_secur,
		uint8_t	req_encr_key_size
	)

Higher layers call this function to check if the current device security settings are sufficient to continue with call establishment.

It is called by call acceptor on reception of LE Credit Based Connection Request.

Parameters

[in]	bd_addr	: BD Address
[in]	req_secur	: Security required
[in]	req_encr_key_size	: Key size

Returns: L2CAP_CONN_OK/L2CAP_BLE_CONN_BAD_AUTHENT/ L2CAP_BLE_CONN_BAD_KEY_SIZE/L2CAP_BLE_CONN_BAD_ENCRYPT/ L2CAP_CONN_NO_RESOURCES.

wiced_bool_t wiced_bt_l2cap_le_disconnect_req ( uint16_t lcid )

Higher layers call this function to disconnect a LE COC channel.

Parameters

[in] lcid Local CID value

Returns: TRUE if disconnect sent, else FALSE

wiced_bool_t wiced_bt_l2cap_le_disconnect_rsp ( uint16_t lcid )

Higher layers call this function to acknowledge the disconnection of a LE COC channel.

Parameters

[in] lcid Local CID value

Returns: void

uint16_t wiced_bt_l2cap_le_get_peer_mtu ( uint16_t lcid )

Higher layers call this function to get peer MTU.

Parameters

[in] lcid : Local CID value

Returns: Peer MTU or 0.

uint16_t wiced_bt_l2cap_le_register	(	uint16_t	le_psm,
		wiced_bt_l2cap_le_appl_information_t *	p_cb_information
	)

Other layers call this function to register L2CAP services for LE_PSM.

Parameters

[in]	le_psm	: LE PSM value
[in]	p_cb_information	: L2CAP cb info

Returns: LE_PSM to use or zero if error. Typically the LE_PSM returned is the same as was passed in, but for an outgoing-only connection a "virtual" LE_PSM is returned and should be used in the calls to wiced_bt_l2cap_le_connect_req() and wiced_bt_l2cap_le_deregister().

wiced_bool_t wiced_bt_l2cap_le_set_user_congestion	(	uint16_t	lcid,
		wiced_bool_t	flow_off_peer
	)

App can call this function to flow control data reception from the peer (flow controlled channels only, viz LE COC, ECRB channels) To stop sending credits/flow off the remote peer set flow_off_peer to WICED_TRUE To resume sending credits/flow on set flow_off_peer to WICED_FALSE.

Note: : This API is typically invoked by applications that buffer incoming data for further processing/forwarding. On invoking the API further issuance of L2CAP credits is stopped, however, the remote will continue to send data till it runs out of credits. The maximum amount of data size expected to be received is 2 * Receive MTU which could be split over a max of (Receive MTU + 2(Sdu header size))/(Receive MPS) number of packets

Parameters

[in]	lcid	: Local CID value
[in]	flow_off_peer	: to flow off peer set to WICED_TRUE, to flow on peer set to WICED_FALSE

Returns: TRUE if command processed OK

uint16_t wiced_bt_l2cap_register	(	uint16_t	psm,
		wiced_bt_l2cap_appl_information_t *	p_cb_information
	)

Other layers call this function to register for L2CAP services.

Parameters

[in]	psm	: PSM value
[in]	p_cb_information	: L2CAP cb info

Returns: PSM to use or zero if error. Typically, the PSM returned is the same as was passed in, but for an outgoing-only connection to a dynamic PSM, a "virtual" PSM is returned and should be used in the calls to wiced_bt_l2cap_connect_req().

wiced_bool_t wiced_bt_l2cap_register_fixed_channel	(	uint16_t	fixed_cid,
		wiced_bt_l2cap_fixed_chnl_reg_t *	p_freg
	)

Register a fixed channel.

Parameters

[in]	fixed_cid	: Fixed Channel #
[in]	p_freg	: Channel Callbacks and config

Returns: TRUE if registered OK

wiced_bool_t wiced_bt_l2cap_remove_fixed_chnl	(	uint16_t	fixed_cid,
		wiced_bt_device_address_t	rem_bda
	)

Remove a fixed channel to a remote device.

Parameters

[in]	fixed_cid	: Fixed CID
[in]	rem_bda	: BD Address of remote Idle timeout to use (or 0xFFFF if don't care)

Returns: TRUE if channel removed

uint16_t wiced_bt_l2cap_send_fixed_chnl_data	(	uint16_t	fixed_cid,
		wiced_bt_device_address_t	rem_bda,
		uint8_t *	p_data,
		uint16_t	data_len
	)

Write data on a fixed signalling channel.

Parameters

[in]	fixed_cid	: Fixed CID
[in]	rem_bda	: BD Address of remote
[in]	p_data	: Pointer to data to send
[in]	data_len	: Length of data to send

Returns: L2CAP_DATAWRITE_SUCCESS, if data accepted L2CAP_DATAWRITE_FAILED, if error

wiced_bool_t wiced_bt_l2cap_set_fixed_channel_timeout	(	wiced_bt_device_address_t	rem_bda,
		uint16_t	fixed_cid,
		uint16_t	idle_timeout
	)

Higher layers call this function to set the idle timeout for a fixed channel.

The "idle timeout" is the amount of time that a connection can remain up with no L2CAP channels on it. A timeout of zero means that the connection will be torn down immediately when the last channel is removed. A timeout of 0xFFFF means no timeout. Values are in seconds. A bd_addr is the remote BD address. If bd_addr = BT_BD_ANY, then the idle timeouts for all active l2cap links will be changed.

Parameters

[in]	rem_bda	: Remote BD address
[in]	fixed_cid	: Fixed CID
[in]	idle_timeout	: Idle timeout

Returns: TRUE if command succeeded, FALSE if failed

wiced_bool_t wiced_bt_l2cap_set_idle_timeout	(	uint16_t	cid,
		uint16_t	timeout,
		wiced_bool_t	is_global
	)

Higher layers call this function to set the idle timeout for a connection, or for all future connections.

The "idle timeout" is the amount of time that a connection can remain up with no L2CAP channels on it. A timeout of zero means that the connection will be torn down immediately when the last channel is removed. A timeout of 0xFFFF means no timeout. Values are in seconds.

Parameters

[in]	cid	: CID value
[in]	timeout	: Timeout value
[in]	is_global	: TRUE, if global

Returns: TRUE if command succeeded, FALSE if failed

wiced_bool_t wiced_bt_l2cap_set_idle_timeout_by_bd_addr	(	wiced_bt_device_address_t	bd_addr,
		uint16_t	timeout,
		wiced_bt_transport_t	transport
	)

Higher layers call this function to set the idle timeout for a connection.

The "idle timeout" is the amount of time that a connection can remain up with no L2CAP channels on it. A timeout of zero means that the connection will be torn down immediately when the last channel is removed. A timeout of 0xFFFF means no timeout. Values are in seconds. A bd_addr is the remote BD address. If bd_addr = BT_BD_ANY, then the idle timeouts for all active l2cap links will be changed.

Parameters

[in]	bd_addr	: BD Address
[in]	timeout	: Timeout value
[in]	transport	: Transport (BR-EDR or LE)

Returns: TRUE if command succeeded, FALSE if failed

Note: This timeout applies to all logical channels active on the ACL link.

wiced_bool_t wiced_bt_l2cap_update_ble_conn_params	(	wiced_bt_device_address_t	rem_bdRa,
		uint16_t	min_int,
		uint16_t	max_int,
		uint16_t	latency,
		uint16_t	timeout
	)

Update LE connection parameters.

Parameters

[in]	rem_bdRa	: Remote BD Address
[in]	min_int	: Min interval, measured in units of 1.25 ms
[in]	max_int	: Max interval, measured in units of 1.25 ms
[in]	latency	: Latency value
[in]	timeout	: Timeout value, measured in units of 10 ms

Returns: : TRUE if update started


			AIROC^™ BTSDK v4.9 - Documentation