PWM Functions. More...

Functions
wiced_bool_t	wiced_hal_pwm_start (uint8_t channel, PwmClockType clk, uint32_t toggleCount, uint32_t initCount, wiced_bool_t invert)
	Configures, enables, and starts the PWM to be active on a preconfigured GPIO pin. More...

wiced_bool_t	wiced_hal_pwm_change_values (uint8_t channel, uint32_t toggleCount, uint32_t initCount)
	Changes the PWM settings after the PWM HW has already been started. More...

uint32_t	wiced_hal_pwm_get_toggle_count (uint8_t channel)
	Returns the current toggle count setting for the corresponding PWM channel. More...

uint32_t	wiced_hal_pwm_get_init_value (uint8_t channel)
	Returns the current initial count setting for the corresponding PWM channel. More...

void	wiced_hal_pwm_disable (uint8_t channel)
	Disables the PWM channel. More...

void	wiced_hal_pwm_enable (uint8_t channel)
	Enables the PWM channel which is already preconfigured. More...

void	wiced_hal_pwm_configure_pin (uint8_t pin, uint8_t PWM)
	Configure any GPIO as any PWM port. More...

wiced_result_t	wiced_hal_pwm_get_params (uint32_t clock_frequency_in, uint32_t duty_cycle, uint32_t pwm_frequency_out, wiced_pwm_config_t *params_out)
	Calculate PWM parameters. More...

Detailed Description

PWM Functions.

Function Documentation

wiced_bool_t wiced_hal_pwm_change_values	(	uint8_t	channel,
		uint32_t	toggleCount,
		uint32_t	initCount
	)

Changes the PWM settings after the PWM HW has already been started.

(!) Note that the maximum width or period of the PWM is 0xFFFF (16-bits).

Parameters

channel	- Desired PWM channel to set [0-5].
toggleCount	- The number of ticks to wait before toggling the signal.
initCount	- Initial value for the counter.

Returns: 1 if PWM was successfully changed, 0 otherwise.

void wiced_hal_pwm_configure_pin	(	uint8_t	pin,
		uint8_t	PWM
	)

Configure any GPIO as any PWM port.

Parameters

pin	: pin to configure as PWM
PWM	which PWM channel to set the pin to (0 - 5)

Returns: VOID

void wiced_hal_pwm_disable ( uint8_t channel )

Disables the PWM channel.

Parameters

channel - Desired PWM channel to stop/disable.

Returns: VOID

void wiced_hal_pwm_enable ( uint8_t channel )

Enables the PWM channel which is already preconfigured.

Parameters

channel - Desired PWM channel to enable.

Returns: VOID

uint32_t wiced_hal_pwm_get_init_value ( uint8_t channel )

Returns the current initial count setting for the corresponding PWM channel.

Parameters

channel - Desired PWM channel from which to obtain the initial count.

Returns: The initial count value of the PWM.

wiced_result_t wiced_hal_pwm_get_params	(	uint32_t	clock_frequency_in,
		uint32_t	duty_cycle,
		uint32_t	pwm_frequency_out,
		wiced_pwm_config_t *	params_out
	)

Calculate PWM parameters.

Parameters

[in]	clock_frequency_in	- in clock frequency
[in]	duty_cycle	- duty cycle in percentage (0 to 100)
[in]	pwm_frequency_out	- Desire PWM output frequency
[out]	params_out	- PWM params

Returns: wiced_result_t

uint32_t wiced_hal_pwm_get_toggle_count ( uint8_t channel )

Returns the current toggle count setting for the corresponding PWM channel.

Parameters

channel - Desired PWM channel from which to obtain the toggle count.

Returns: The value at which the PWM is going to toggle.

wiced_bool_t wiced_hal_pwm_start	(	uint8_t	channel,
		PwmClockType	clk,
		uint32_t	toggleCount,
		uint32_t	initCount,
		wiced_bool_t	invert
	)

Configures, enables, and starts the PWM to be active on a preconfigured GPIO pin.

(!) Note that the desired GPIO pin must have already been configured as output. See the HW muxing section in the Kit Guide or HW User Manual for your device for more information.

Parameters

channel	- Desired PWM channel to use [0-5].
clk	- PMU_CLK or LHL_CLK
toggleCount	- The number of ticks to wait before toggling the signal.
initCount	- Initial value for the counter.
invert	- 1 to invert the signal.

Returns: 1 if PWM was successfully started, 0 otherwise.

The following example outputs a signal on P28 using the PMU clock.

(!) Note that the maximum width or period of the PWM is 0xFFFF (16-bits).

(!) Note that if you use PMU_CLK instead of LHL_CLK, a call to wiced_hal_aclk_enable() is required. When configuring aclk, ACLK0 is not avaliable for use with PWM–only ACLK1.

(!) Note that each PWM<#> channel corresponds to a specific GPIO pin, and said pin must be configured for output before PWM may use it. Please reference the User Documentation for more information on which pins support PWM on your platform.

Parameters

channel	- Desired PWM channel to use [0-5].
clk	- PMU_CLK or LHL_CLK
toggleCount	- The number of ticks to wait before toggling the signal.
initCount	- Initial value for the counter.
invert	- 1 to invert the signal.

Returns: 1 if PWM was successfully started, 0 otherwise.


			AIROC^™ BTSDK v4.0 - Documentation