DMA (Direct Memory Access)

General Description

High level interface for interacting with the direct memory access (DMA).

The DMA driver allows for initializing and configuring a DMA channel in order to trigger data transfers to and from memory and peripherals. The transfers occur independently of the CPU and can be triggered by software or hardware. Multiple channels can be active at the same time each with their own user-selectable priority and transfer characteristics.

Features

• CPU independent memory access
• Access to memory and peripherals
• Multiple independent channels
• Configurable transer sizes and bursts
• Configurable priorities
• Event completion notification

Flow

The operational flow of the driver is listed below. This shows the basic order in which each of the functions would generally be called. While Initialize must always be first and Release always last, with care, the other functions can be reordered based on the implementation needs.

1. Initialize: cyhal_dma_init or cyhal_dma_init_adv or cyhal_dma_init_cfg
2. Configure: cyhal_dma_configure
3. Setup: cyhal_dma_register_callback, cyhal_dma_enable_event, cyhal_dma_connect_digital, or cyhal_dma_enable_output
4. Enable: cyhal_dma_enable
5. Trigger: cyhal_dma_start_transfer or via a hardware signal
6. Status/ReEnable (optional): cyhal_dma_is_busy, cyhal_dma_enable
7. Cleanup (optional): cyhal_dma_disable, cyhal_dma_enable_event, cyhal_dma_disconnect_digital, or cyhal_dma_disable_output
8. Release (optional): cyhal_dma_free

Quick Start

See Snippet 1: Simple DMA initialization and transfer for a code snippet that sets up a DMA transfer to move memory from one location to another.

Code snippets

Note

Error handling code has been intentionally left out of snippets to highlight API usage.

Snippet 1: Simple DMA initialization and transfer

The following snippet initializes a DMA channel and uses it to transfer a a single block of memory. The DMA channel is reserved by calling cyhal_dma_init. It then needs to be configured with cyhal_dma_configure and then the transfer is started with cyhal_dma_start_transfer.
If the DMA channel is not needed anymore, it can be released by calling cyhal_dma_free

    cy_rslt_t       rslt;
    cyhal_dma_t     dma;
    cyhal_dma_cfg_t cfg =
    {
        .src_addr       = 0x8000000,               // Start from address
        .src_increment  = 1,                       // Increment source by 1 word
        .dst_addr       = 0x8001000,               // Destination from address
        .dst_increment  = 1,                       // Increment destination by 1 word
        .transfer_width = 32,                      // 32 bit transfer
        .length         = 0x10,                    // Transfer 64 bytes (16 transfers of 4 bytes)
        .burst_size     = 0,                       // Transfer everything in a single burst
        .action         = CYHAL_DMA_TRANSFER_FULL, // Notify when everything is done
    };

    // Allocate the DMA channel for use
    rslt = cyhal_dma_init(&dma, CYHAL_DMA_PRIORITY_DEFAULT, CYHAL_DMA_DIRECTION_MEM2MEM);

    // Configure the channel for the upcoming transfer
    rslt = cyhal_dma_configure(&dma, &cfg);

    // Begin the transfer
    rslt = cyhal_dma_start_transfer(&dma);


    // If the DMA channel is no longer needed, it can be freed up for other uses
    if (!cyhal_dma_is_busy(&dma))
    {
        cyhal_dma_free(&dma);
    }

Snippet 2: Configuring the DMA channel based on memory requirements

cyhal_dma_configure can be used after DMA initialization to handle a variety of memory layouts.

    #define BUFFER_SIZE (32)
    #define PERIPHERAL_FIFO_ADDR (0x4001000)

    cy_rslt_t   rslt;
    cyhal_dma_t dma;
    uint32_t    buffer[BUFFER_SIZE];

    // Allocate the DMA channel for transfering from memory to a peripheral
    rslt = cyhal_dma_init(&dma, CYHAL_DMA_PRIORITY_DEFAULT, CYHAL_DMA_DIRECTION_MEM2PERIPH);

    cyhal_dma_cfg_t cfg =
    {
        .src_addr       = (uint32_t)buffer,        // Start from address
        .src_increment  = 1,                       // Increment source by 1 word
        .dst_addr       = PERIPHERAL_FIFO_ADDR,    // Destination from address
        .dst_increment  = 0,                       // Don't increment the destination
        .transfer_width = 32,                      // 32 bit transfer
        .length         = BUFFER_SIZE,             // Transfer 64 bytes (16 transfers of 4 bytes)
        .burst_size     = 0,                       // Transfer everything in a single burst
        .action         = CYHAL_DMA_TRANSFER_FULL, // Notify when everything is done
    };
    rslt = cyhal_dma_configure(&dma, &cfg);

Snippet 3: Interrupts and retriggering DMA transfers

DMA events like transfer complete or error events can be used to trigger a callback function.
This snippet uses cyhal_dma_configure to break the full transfer into multiple bursts. This allows higher priority items access to the memory bus if necessary while the DMA operation is still in progress. It then uses cyhal_dma_enable_event() to enable the transfer complete event to trigger the callback function registered by cyhal_dma_register_callback().

void dma_event_callback(void* callback_arg, cyhal_dma_event_t event)
{
    CY_UNUSED_PARAMETER(event);
    cyhal_dma_t* dma = (cyhal_dma_t*)callback_arg;

    // Do work specific to each burst complete

    // If all bursts are complete, start another
    if (!cyhal_dma_is_busy(dma))
    {
        cyhal_dma_start_transfer(dma);
    }
}


cy_rslt_t snippet_cyhal_dma_events()
{
    cy_rslt_t       rslt;
    cyhal_dma_t     dma;
    cyhal_dma_cfg_t cfg =
    {
        .src_addr       = 0x8000000,                // Start from address
        .src_increment  = 1,                        // Increment source by 1 word
        .dst_addr       = 0x8001000,                // Destination from address
        .dst_increment  = 1,                        // Increment destination by 1 word
        .transfer_width = 32,                       // 32 bit transfer
        .length         = 0x10,                     // Transfer 64 bytes (16 transfers of 4 bytes)
        .burst_size     = 4,                        // Transfer 4 words a a time
        .action         = CYHAL_DMA_TRANSFER_BURST, // Notify when each burst is done
    };

    // Allocate the DMA channel for use
    rslt = cyhal_dma_init(&dma, CYHAL_DMA_PRIORITY_LOW, CYHAL_DMA_DIRECTION_MEM2MEM);
    CY_ASSERT(CY_RSLT_SUCCESS == rslt);

    // Configure the channel for the upcoming transfer
    if (CY_RSLT_SUCCESS == rslt)
    {
        rslt = cyhal_dma_configure(&dma, &cfg);
    }

    // Register an event callback handler and enable events
    if (CY_RSLT_SUCCESS == rslt)
    {
        cyhal_dma_register_callback(&dma, &dma_event_callback, &dma);
        cyhal_dma_enable_event(&dma, CYHAL_DMA_TRANSFER_COMPLETE, CYHAL_ISR_PRIORITY_DEFAULT, true);

        // Begin the transfer
        rslt = cyhal_dma_start_transfer(&dma);
    }

    return rslt;
}

Snippet 4: Using hardware signals with DMA

DMA operations can be initiated by a hardware signal, or initiate a hardware signal on completion.
This snippet shows how either can be done with a timer object.

Note

Not all devices have the same internal connections. As a result, it may not be possible to setup connections exactly as shown in the snippet on your device.

In the first case, the DMA output signal (cyhal_dma_enable_output) is used so that when the DMA operation complets it in turn causes the timer to run.
NOTE: The cyhal_dma_init_adv can also be used insted of cyhal_dma_enable_output to enable the output. The advantage of using init_adv is it makes sure the DMA instance that is allocated is able to connected to the specified signal.

    rslt = cyhal_dma_init(&dma, 1, CYHAL_DMA_DIRECTION_PERIPH2PERIPH);
    rslt = cyhal_dma_configure(&dma, &dma_config);
    rslt = cyhal_dma_enable_output(&dma, CYHAL_DMA_OUTPUT_TRIGGER_ALL_ELEMENTS, &source);

    rslt = cyhal_timer_connect_digital(&timer, source, CYHAL_TIMER_INPUT_START);

    // starting the DMA transfers data and then starts the timer
    //CY_ASSERT(cyhal_timer_read(&timer) == 0); // timer not started
    rslt = cyhal_dma_start_transfer(&dma);
    while (cyhal_dma_is_busy(&dma))
    {
        cyhal_system_delay_ms(1);
    }

    // DMA completed, and timer has started
    //CY_ASSERT(src == dst);
    //CY_ASSERT(cyhal_timer_read(&timer) > 0);

The second snippet shows how a timer overflow can be used to trigger a DMA operation. It uses cyhal_dma_init_adv to setup the connection, but cyhal_dma_connect_digital could be used instead; with the same note as above about ensuring a connection between instances.

    rslt = cyhal_timer_enable_output(&timer, CYHAL_TIMER_OUTPUT_OVERFLOW, &source);

    cyhal_dma_src_t dma_src =
    {
        .source = source,
        .input  = CYHAL_DMA_INPUT_TRIGGER_ALL_ELEMENTS,
    };
    rslt = cyhal_dma_init_adv(&dma, &dma_src, NULL, NULL, 1, CYHAL_DMA_DIRECTION_PERIPH2MEM);
    rslt = cyhal_dma_configure(&dma, &dma_config);


    //CY_ASSERT(src != dst);    // values do not match before DMA
    cyhal_timer_start(&timer);  // start the timer that will trigger DMA
    cyhal_system_delay_ms(100); // give plenty of time for timer and DMA to finish
    //CY_ASSERT(src == dst);    // values now match after DMA finishes

API Reference
	DMA HAL Results
	DMA specific return codes.

Data Structures
struct	cyhal_dma_cfg_t
	Configuration of a DMA channel. More...
struct	cyhal_dma_src_t
	DMA input connection information to setup while initializing the driver. More...
struct	cyhal_dma_dest_t
	DMA output connection information to setup while initializing the driver. More...

Macros
#define	cyhal_dma_init(obj, priority, direction)   (cyhal_dma_init_adv(obj, NULL, NULL, NULL, priority, direction))
	Initialize the DMA peripheral. More...

Typedefs
typedef void(*	cyhal_dma_event_callback_t) (void *callback_arg, cyhal_dma_event_t event)
	Event handler for DMA interrupts.

Enumerations
enum	cyhal_dma_direction_t {   CYHAL_DMA_DIRECTION_MEM2MEM,   CYHAL_DMA_DIRECTION_MEM2PERIPH,   CYHAL_DMA_DIRECTION_PERIPH2MEM,   CYHAL_DMA_DIRECTION_PERIPH2PERIPH }
	Direction for DMA transfers. More...
enum	cyhal_dma_event_t {   CYHAL_DMA_NO_INTR = 0,   CYHAL_DMA_TRANSFER_COMPLETE = 1 << 0,   CYHAL_DMA_DESCRIPTOR_COMPLETE = 1 << 1,   CYHAL_DMA_SRC_BUS_ERROR = 1 << 2,   CYHAL_DMA_DST_BUS_ERROR = 1 << 3,   CYHAL_DMA_SRC_MISAL = 1 << 4,   CYHAL_DMA_DST_MISAL = 1 << 5,   CYHAL_DMA_CURR_PTR_NULL = 1 << 6,   CYHAL_DMA_ACTIVE_CH_DISABLED = 1 << 7,   CYHAL_DMA_DESCR_BUS_ERROR = 1 << 8 }
	Flags enum of DMA events. More...
enum	cyhal_dma_input_t {   CYHAL_DMA_INPUT_TRIGGER_SINGLE_ELEMENT,   CYHAL_DMA_INPUT_TRIGGER_SINGLE_BURST,   CYHAL_DMA_INPUT_TRIGGER_ALL_ELEMENTS }
	Specifies the transfer type to trigger when an input signal is received. More...
enum	cyhal_dma_output_t {   CYHAL_DMA_OUTPUT_TRIGGER_SINGLE_ELEMENT,   CYHAL_DMA_OUTPUT_TRIGGER_SINGLE_BURST,   CYHAL_DMA_OUTPUT_TRIGGER_ALL_ELEMENTS }
	Specifies the transfer completion event that triggers a signal output. More...
enum	cyhal_dma_transfer_action_t {   CYHAL_DMA_TRANSFER_BURST,   CYHAL_DMA_TRANSFER_FULL,   CYHAL_DMA_TRANSFER_BURST_DISABLE,   CYHAL_DMA_TRANSFER_FULL_DISABLE }
	This defines the behavior of the the channel when transfers are initiated. More...

Functions
cy_rslt_t	cyhal_dma_init_adv (cyhal_dma_t *obj, cyhal_dma_src_t *src, cyhal_dma_dest_t *dest, cyhal_source_t *dest_source, uint8_t priority, cyhal_dma_direction_t direction)
	Initialize the DMA peripheral. More...
cy_rslt_t	cyhal_dma_init_cfg (cyhal_dma_t *obj, const cyhal_dma_configurator_t *cfg)
	Initialize the DMA peripheral using data provided by the configurator. More...
void	cyhal_dma_free (cyhal_dma_t *obj)
	Free the DMA object. More...
cy_rslt_t	cyhal_dma_configure (cyhal_dma_t *obj, const cyhal_dma_cfg_t *cfg)
	Setup the DMA channel behavior. More...
cy_rslt_t	cyhal_dma_enable (cyhal_dma_t *obj)
	Enable the DMA transfer so that it can start transferring data when triggered. More...
cy_rslt_t	cyhal_dma_disable (cyhal_dma_t *obj)
	Disable the DMA transfer so that it does not continue to trigger. More...
cy_rslt_t	cyhal_dma_start_transfer (cyhal_dma_t *obj)
	Initiates DMA channel transfer for specified DMA object. More...
bool	cyhal_dma_is_busy (cyhal_dma_t *obj)
	Checks if the transfer has been triggered, but not yet complete (eg: is pending, blocked or running) More...
void	cyhal_dma_register_callback (cyhal_dma_t *obj, cyhal_dma_event_callback_t callback, void *callback_arg)
	Register a DMA callback handler. More...
void	cyhal_dma_enable_event (cyhal_dma_t *obj, cyhal_dma_event_t event, uint8_t intr_priority, bool enable)
	Configure DMA event enablement. More...
cy_rslt_t	cyhal_dma_connect_digital (cyhal_dma_t *obj, cyhal_source_t source, cyhal_dma_input_t input)
	Connects a source signal and enables the specified input to the DMA channel. More...
cy_rslt_t	cyhal_dma_enable_output (cyhal_dma_t *obj, cyhal_dma_output_t output, cyhal_source_t *source)
	Enables the specified output signal from a DMA channel that is triggered when a transfer is completed. More...
cy_rslt_t	cyhal_dma_disconnect_digital (cyhal_dma_t *obj, cyhal_source_t source, cyhal_dma_input_t input)
	Disconnects a source signal and disables the specified input to the DMA channel. More...
cy_rslt_t	cyhal_dma_disable_output (cyhal_dma_t *obj, cyhal_dma_output_t output)
	Disables the specified output signal from a DMA channel. More...

---

Data Structure Documentation

cyhal_dma_cfg_t

struct cyhal_dma_cfg_t

Data Fields
uint32_t	src_addr	Source address.
int16_t	src_increment	Source address auto increment amount in multiples of transfer_width.
uint32_t	dst_addr	Destination address.
int16_t	dst_increment	Destination address auto increment amount in multiples of transfer_width.
uint8_t	transfer_width	Transfer width in bits. Valid values are: 8, 16, or 32.
uint32_t	length	Number of elements to be transferred in total.
uint32_t	burst_size	Number of elements to be transferred per trigger. If set to 0 every element is transferred, otherwise burst_size must evenly divide length.
cyhal_dma_transfer_action_t	action	Sets the behavior of the channel when triggered (using start_transfer). Ignored if burst_size is not configured.

cyhal_dma_src_t

struct cyhal_dma_src_t

Data Fields
cyhal_source_t	source	Source of signal to DMA; obtained from another driver's cyhal_<PERIPH>_enable_output.
cyhal_dma_input_t	input	DMA input signal to be driven.

cyhal_dma_dest_t

struct cyhal_dma_dest_t

Data Fields
cyhal_dma_output_t	output	Output signal of DMA.
cyhal_dest_t	dest	Destination of DMA signal.

Macro Definition Documentation

cyhal_dma_init

#define cyhal_dma_init	(		obj,
			priority,
			direction
	)		(cyhal_dma_init_adv(obj, NULL, NULL, NULL, priority, direction))

Initialize the DMA peripheral.

Parameters

[out]	obj	Pointer to a DMA object. The caller must allocate the memory for this object but the init function will initialize its contents.
[in]	priority	The priority of this DMA operation relative to others. The number of priority levels which are supported is hardware dependent. All implementations define a CYHAL_DMA_PRIORITY_DEFAULT constant which is always valid. If supported, implementations will also define CYHAL_DMA_PRIORITY_HIGH, CYHAL_DMA_PRIORITY_MEDIUM, and CYHAL_DMA_PRIORITY_LOW. The behavior of any other value is implementation defined. See the implementation-specific DMA documentation for more details.
[in]	direction	The direction memory is copied

Returns

The status of the init request

Enumeration Type Documentation

cyhal_dma_direction_t

enum cyhal_dma_direction_t

Direction for DMA transfers.

Enumerator
CYHAL_DMA_DIRECTION_MEM2MEM	Memory to memory.
CYHAL_DMA_DIRECTION_MEM2PERIPH	Memory to peripheral.
CYHAL_DMA_DIRECTION_PERIPH2MEM	Peripheral to memory.
CYHAL_DMA_DIRECTION_PERIPH2PERIPH	Peripheral to peripheral.

cyhal_dma_event_t

enum cyhal_dma_event_t

Flags enum of DMA events.

Multiple events can be enabled via cyhal_dma_enable_event and the callback from cyhal_dma_register_callback will be run to notify.

Enumerator
CYHAL_DMA_NO_INTR	No interrupt.
CYHAL_DMA_TRANSFER_COMPLETE	Indicates that an individual transfer (burst or full) has completed based on the specified cyhal_dma_transfer_action_t.
CYHAL_DMA_DESCRIPTOR_COMPLETE	Indicates that the full transfer has completed.
CYHAL_DMA_SRC_BUS_ERROR	Indicates that there is a source bus error.
CYHAL_DMA_DST_BUS_ERROR	Indicates that there is a destination bus error.
CYHAL_DMA_SRC_MISAL	Indicates that the source address is not aligned.
CYHAL_DMA_DST_MISAL	Indicates that the destination address is not aligned.
CYHAL_DMA_CURR_PTR_NULL	Indicates that the current descriptor pointer is null.
CYHAL_DMA_ACTIVE_CH_DISABLED	Indicates that the active channel is disabled.
CYHAL_DMA_DESCR_BUS_ERROR	Indicates that there has been a descriptor bus error.

cyhal_dma_input_t

enum cyhal_dma_input_t

Specifies the transfer type to trigger when an input signal is received.

Enumerator
CYHAL_DMA_INPUT_TRIGGER_SINGLE_ELEMENT	Transfer a single element when an input signal is received.
CYHAL_DMA_INPUT_TRIGGER_SINGLE_BURST	Transfer a single burst when an input signal is received.
CYHAL_DMA_INPUT_TRIGGER_ALL_ELEMENTS	Transfer all elements when an input signal is received.

cyhal_dma_output_t

enum cyhal_dma_output_t

Specifies the transfer completion event that triggers a signal output.

Enumerator
CYHAL_DMA_OUTPUT_TRIGGER_SINGLE_ELEMENT	Trigger an output when a single element is transferred.
CYHAL_DMA_OUTPUT_TRIGGER_SINGLE_BURST	Trigger an output when a single burst is transferred.
CYHAL_DMA_OUTPUT_TRIGGER_ALL_ELEMENTS	Trigger an output when all elements are transferred.

cyhal_dma_transfer_action_t

enum cyhal_dma_transfer_action_t

This defines the behavior of the the channel when transfers are initiated.

It can specify both how the transfer is broken up and what happens at the end of the transfer. If burst_size from cyhal_dma_cfg_t is used, this specifies the granularity of operations that occur. Using CYHAL_DMA_TRANSFER_BURST or CYHAL_DMA_TRANSFER_BURST_DISABLE means a single trigger will transfer a single burst (of burst_size) and raise the CYHAL_DMA_TRANSFER_COMPLETE interrupt. Using CYHAL_DMA_TRANSFER_FULL means a single trigger will transfer all bursts (total size length) and raise the CYHAL_DMA_TRANSFER_COMPLETE interrupt. If burst_size is not used, this has no impact and a single trigger will perform a complete transfer and raise a single interrupt at the end. When the transfer is complete, the channel can be left enabled, or automatically disabled. When left enabled (CYHAL_DMA_TRANSFER_BURST or CYHAL_DMA_TRANSFER_FULL) subsequent triggers will re-start the transfers. If the channel is diabled on completion (CYHAL_DMA_TRANSFER_BURST_DISABLE or CYHAL_DMA_TRANSFER_FULL_DISABLE), cyhal_dma_configure must be called to reconfigure the channel for future transfers.

Note

When using cyhal_dma_connect_digital for a hardware input trigger, the cyhal_dma_input_t argument defines how much of the transfer is initiated at a time. This enum will still define when interrupts are raised.

Enumerator
CYHAL_DMA_TRANSFER_BURST	A single burst is triggered and a CYHAL_DMA_TRANSFER_COMPLETE will occur after each burst. The channel will be left enabled and can continue to be triggered.
CYHAL_DMA_TRANSFER_FULL	All bursts are triggered and a single CYHAL_DMA_TRANSFER_COMPLETE will occur at the end. The channel will be left enabled and can continue to be triggered.
CYHAL_DMA_TRANSFER_BURST_DISABLE	A single burst is triggered and a CYHAL_DMA_TRANSFER_COMPLETE will occur after each burst. When all bursts are complete, the channel will be disabled.
CYHAL_DMA_TRANSFER_FULL_DISABLE	All bursts are triggered and a single CYHAL_DMA_TRANSFER_COMPLETE will occur at the end. When complete, the channel will be disabled.

Function Documentation

cyhal_dma_init_adv()

cy_rslt_t cyhal_dma_init_adv	(	cyhal_dma_t *	obj,
		cyhal_dma_src_t *	src,
		cyhal_dma_dest_t *	dest,
		cyhal_source_t *	dest_source,
		uint8_t	priority,
		cyhal_dma_direction_t	direction
	)

Initialize the DMA peripheral.

If a source signal is provided for src, this will connect the provided signal to the DMA just as would be done by calling cyhal_dma_connect_digital. Similarly, if a destination target is provided for dest this will enable the specified output just as would be done by calling cyhal_dma_enable_output.

Parameters

[out]	obj	Pointer to a DMA object. The caller must allocate the memory for this object but the init function will initialize its contents.
[in]	src	An optional source signal to connect to the DMA
[in]	dest	An optional destination singal to drive from the DMA
[out]	dest_source	An optional pointer to user-allocated source signal object which will be initialized by enable_output. If dest is non-null, this must also be non-null. dest_source should be passed to (dis)connect_digital functions to (dis)connect the associated endpoints.
[in]	priority	The priority of this DMA operation relative to others. The number of priority levels which are supported is hardware dependent. All implementations define a CYHAL_DMA_PRIORITY_DEFAULT constant which is always valid. If supported, implementations will also define CYHAL_DMA_PRIORITY_HIGH, CYHAL_DMA_PRIORITY_MEDIUM, and CYHAL_DMA_PRIORITY_LOW. The behavior of any other value is implementation defined. See the implementation-specific DMA documentation for more details.
[in]	direction	The direction memory is copied

Returns

The status of the init request

cyhal_dma_init_cfg()

cy_rslt_t cyhal_dma_init_cfg	(	cyhal_dma_t *	obj,
		const cyhal_dma_configurator_t *	cfg
	)

Initialize the DMA peripheral using data provided by the configurator.

Note

Depending on what the configurator allows filling it, it is likely that at least the source and destination addresses of the transfer(s) still need to be setup.

Parameters

[out]	obj	Pointer to a DMA object. The caller must allocate the memory for this object but the init function will initialize its contents.
[in]	cfg	Configuration structure generated by a configurator.

Returns

The status of the init request

cyhal_dma_free()

void cyhal_dma_free

(

cyhal_dma_t *

obj

)

Free the DMA object.

Freeing a DMA object while a transfer is in progress (cyhal_dma_is_busy) is invalid.

Parameters

[in,out]

obj

The DMA object

cyhal_dma_configure()

cy_rslt_t cyhal_dma_configure	(	cyhal_dma_t *	obj,
		const cyhal_dma_cfg_t *	cfg
	)

Setup the DMA channel behavior.

This will also enable the channel to allow it to be triggered. The transfer can be software triggered by calling cyhal_dma_start_transfer or by hardware. A hardware input signal is setup by cyhal_dma_connect_digital or cyhal_dma_init_adv.

Note

If hardware triggers are used, any necessary event callback setup (cyhal_dma_register_callback and cyhal_dma_enable_event) should be done before calling this function to ensure the handlers are in place before the transfer can happen.

The automatic enablement of the channel as part of this function is expected to change in a future update. This would only happen on a new major release (eg: 1.0 -> 2.0).

If the DMA was setup using cyhal_dma_init_cfg, this function should not be used.

Parameters

[in]	obj	The DMA object
[in]	cfg	Configuration parameters for the transfer

Returns

The status of the configure request

cyhal_dma_enable()

cy_rslt_t cyhal_dma_enable

(

cyhal_dma_t *

obj

)

Enable the DMA transfer so that it can start transferring data when triggered.

A trigger is caused either by calling cyhal_dma_start_transfer or by hardware as a result of a connection made in either cyhal_dma_connect_digital or cyhal_dma_init_adv. The DMA can be disabled by calling cyhal_dma_disable or by setting the cyhal_dma_cfg_t action to CYHAL_DMA_TRANSFER_BURST_DISABLE, or CYHAL_DMA_TRANSFER_FULL_DISABLE.

Parameters

[in]

obj

The DMA object

Returns

The status of the enable request

cyhal_dma_disable()

cy_rslt_t cyhal_dma_disable

(

cyhal_dma_t *

obj

)

Disable the DMA transfer so that it does not continue to trigger.

It can be reenabled by calling cyhal_dma_enable or cyhal_dma_configure.

Parameters

[in]

obj

The DMA object

Returns

The status of the enable request

cyhal_dma_start_transfer()

cy_rslt_t cyhal_dma_start_transfer

(

cyhal_dma_t *

obj

)

Initiates DMA channel transfer for specified DMA object.

This should only be done after the channel has been configured (cyhal_dma_configure) and any necessary event callbacks setup (cyhal_dma_register_callback cyhal_dma_enable_event)

Parameters

[in]

obj

The DMA object

Returns

The status of the start_transfer request

cyhal_dma_is_busy()

bool cyhal_dma_is_busy

(

cyhal_dma_t *

obj

)

Checks if the transfer has been triggered, but not yet complete (eg: is pending, blocked or running)

Parameters

[in]

obj

The DMA object

Returns

True if DMA channel is busy

cyhal_dma_register_callback()

void cyhal_dma_register_callback	(	cyhal_dma_t *	obj,
		cyhal_dma_event_callback_t	callback,
		void *	callback_arg
	)

Register a DMA callback handler.

This function will be called when one of the events enabled by cyhal_dma_enable_event occurs.

Parameters

[in]	obj	The DMA object
[in]	callback	The callback handler which will be invoked when an event triggers
[in]	callback_arg	Generic argument that will be provided to the callback when called

cyhal_dma_enable_event()

void cyhal_dma_enable_event	(	cyhal_dma_t *	obj,
		cyhal_dma_event_t	event,
		uint8_t	intr_priority,
		bool	enable
	)

Configure DMA event enablement.

When an enabled event occurs, the function specified by cyhal_dma_register_callback will be called.

Parameters

[in]	obj	The DMA object
[in]	event	The DMA event type
[in]	intr_priority	The priority for NVIC interrupt events. The priority from the most recent call will take precedence, i.e all events will have the same priority.
[in]	enable	True to turn on interrupts, False to turn off

cyhal_dma_connect_digital()

cy_rslt_t cyhal_dma_connect_digital	(	cyhal_dma_t *	obj,
		cyhal_source_t	source,
		cyhal_dma_input_t	input
	)

Connects a source signal and enables the specified input to the DMA channel.

This connection can also be setup automatically on initialization via cyhal_dma_init_adv. If the signal needs to be disconnected later, cyhal_dma_disconnect_digital can be used.

Parameters

[in]	obj	The DMA object
[in]	source	Source signal obtained from another driver's cyhal_<PERIPH>_enable_output
[in]	input	Which input to enable

Returns

The status of the connection

cyhal_dma_enable_output()

cy_rslt_t cyhal_dma_enable_output	(	cyhal_dma_t *	obj,
		cyhal_dma_output_t	output,
		cyhal_source_t *	source
	)

Enables the specified output signal from a DMA channel that is triggered when a transfer is completed.

This can also be setup automatically on initialization via cyhal_dma_init_adv. If the output is not needed in the future, cyhal_dma_disable_output can be used.

Parameters

[in]	obj	The DMA object
[in]	output	Which event triggers the output
[out]	source	Pointer to user-allocated source signal object which will be initialized by enable_output. source should be passed to (dis)connect_digital functions to (dis)connect the associated endpoints.

Returns

The status of the output enable

cyhal_dma_disconnect_digital()

cy_rslt_t cyhal_dma_disconnect_digital	(	cyhal_dma_t *	obj,
		cyhal_source_t	source,
		cyhal_dma_input_t	input
	)

Disconnects a source signal and disables the specified input to the DMA channel.

This removes the connection that was established by either cyhal_dma_init_adv or cyhal_dma_connect_digital.

Parameters

[in]	obj	The DMA object
[in]	source	Source signal from cyhal_<PERIPH>_enable_output to disable
[in]	input	Which input to disable

Returns

The status of the disconnect

cyhal_dma_disable_output()

cy_rslt_t cyhal_dma_disable_output	(	cyhal_dma_t *	obj,
		cyhal_dma_output_t	output
	)

Disables the specified output signal from a DMA channel.

This turns off the signal that was enabled by either cyhal_dma_init_adv or cyhal_dma_enable_output. It is recommended that the signal is disconnected (cyhal_<PERIPH>_disconnect_digital) from anything it might be driving before being disabled.

Parameters

[in]	obj	The DMA object
[in]	output	Which output to disable

Returns

The status of the disablement