AIROC™ BTSDK v4.9 - Documentation | ||||
This file contains L2CAP protocol definitions. More...
Macros | |
#define | L2CAP_PKT_START_FLUSHABLE 2 |
#define | L2CAP_PKT_START_NON_FLUSHABLE 0 |
#define | L2CAP_COMPLETE_FLUSHABLE_PKT 3 /* complete flushable L2CAP packet */ |
#define | L2CAP_PKT_START 2 |
#define | L2CAP_PKT_CONTINUE 1 |
#define | L2CAP_MASK_FLAG 0x0FFF |
#define | L2CAP_PKT_TYPE_SHIFT 12 |
#define | L2CAP_PKT_TYPE_MASK 3 |
#define | L2CAP_BLE_CONN_MIN_MPS_SIZE 23 |
#define | L2CAP_BLE_CONN_MAX_MPS_SIZE 65533 |
#define | L2CAP_BLE_CONN_MIN_MTU_SIZE 23 |
#define | L2CAP_CRB_CONN_SDU_LEN_FIELD_SIZE 2 /* Applies to LE-COC and ECRB channel types */ |
#define | L2CAP_CONN_TIMEOUT 0xEEEE |
Connection timeout. More... | |
#define | L2CAP_CONN_REJECTED 253 |
Connection reject. More... | |
#define | L2CAP_CONN_AMP_FAILED 254 |
Connection failed. More... | |
#define | L2CAP_CONN_NO_LINK 255 |
NO Link. More... | |
#define | L2CAP_CONN_CANCEL 256 |
L2CAP connection cancelled. More... | |
#define | L2CAP_MOVE_CFM_OK 0 |
Channel Move confirm Ok. | |
#define | L2CAP_MOVE_CFM_REFUSED 1 |
Channel Move confirm Refused. | |
#define | L2CAP_CMD_REJ_NOT_UNDERSTOOD 0 |
Command Not Understood. | |
#define | L2CAP_CMD_REJ_MTU_EXCEEDED 1 |
MTU Exceeded. | |
#define | L2CAP_CMD_REJ_INVALID_CID 2 |
Invalid CID. | |
#define | L2CAP_CFG_FLAGS_MASK_CONT 0x0001 |
Flags mask: Continuation. | |
#define | L2CAP_CFG_FCS_BYPASS 0 |
Bypass the FCS in streaming or ERTM modes. | |
#define | L2CAP_CFG_FCS_USE 1 |
Use the FCS in streaming or ERTM modes [default]. | |
#define | L2CAP_NO_AUTOMATIC_FLUSH 0xFFFF |
No Automatic Flush. | |
#define | L2CAP_NO_RETRANSMISSION 0x0001 |
No Retranmission. | |
#define | L2CAP_DEFAULT_MTU (672) |
Default MTU. | |
#define | L2CAP_DEFAULT_FLUSH_TO L2CAP_NO_AUTOMATIC_FLUSH |
Default Flush settings. | |
#define | L2CAP_DEFAULT_SERV_TYPE 1 |
Default service type. | |
#define | L2CAP_DEFAULT_TOKEN_RATE 0 |
Default Token rate. | |
#define | L2CAP_DEFAULT_BUCKET_SIZE 0 |
Default Bucket size. | |
#define | L2CAP_DEFAULT_PEAK_BANDWIDTH 0 |
Default Peak bandwidth. | |
#define | L2CAP_DEFAULT_LATENCY 0xFFFFFFFF |
Default Letency. | |
#define | L2CAP_DEFAULT_DELAY 0xFFFFFFFF |
Default Delay. | |
#define | L2CAP_DEFAULT_FCS L2CAP_CFG_FCS_USE |
Default FCS settings. | |
#define | L2CAP_DISC_OK 0 |
L2CAP Disconnect Success. | |
#define | L2CAP_DISC_TIMEOUT 0xEEEE |
L2CAP Disconnection Timeout. | |
#define | L2CAP_INFO_RESP_RESULT_SUCCESS 0 |
L2CAP Info response success. | |
#define | L2CAP_INFO_RESP_RESULT_NOT_SUPPORTED 1 |
L2CAP info response result not supported. | |
#define | L2CAP_CONNLESS_MTU_INFO_TYPE 0x0001 |
Connection less MTU info type. | |
#define | L2CAP_EXTENDED_FEATURES_INFO_TYPE 0x0002 |
Extended feature Info Type. More... | |
#define | L2CAP_FIXED_CHANNELS_INFO_TYPE 0x0003 |
Fix channel Info Type. More... | |
#define | L2CAP_CONNLESS_MTU_INFO_SIZE 2 |
Connectionless MTU size. | |
#define | L2CAP_EXTENDED_FEATURES_ARRAY_SIZE 4 |
Extended features array size. | |
#define | L2CAP_FIXED_CHNL_ARRAY_SIZE 8 |
Fixed channel array size. | |
#define | L2CAP_EXTFEA_RTRANS 0x00000001 |
Retransmission Mode (Not Supported) | |
#define | L2CAP_EXTFEA_FC 0x00000002 |
Flow Control Mode (Not Supported) | |
#define | L2CAP_EXTFEA_QOS 0x00000004 |
QOS Mode. | |
#define | L2CAP_EXTFEA_ENH_RETRANS 0x00000008 |
Enhanced retransmission mode. | |
#define | L2CAP_EXTFEA_STREAM_MODE 0x00000010 |
Streaming Mode. | |
#define | L2CAP_EXTFEA_NO_CRC 0x00000020 |
Optional FCS (if set No FCS desired) | |
#define | L2CAP_EXTFEA_EXT_FLOW_SPEC 0x00000040 |
Extended flow spec. | |
#define | L2CAP_EXTFEA_FIXED_CHNLS 0x00000080 |
Fixed channels. | |
#define | L2CAP_EXTFEA_EXT_WINDOW 0x00000100 |
Extended Window Size. | |
#define | L2CAP_EXTFEA_UCD_RECEPTION 0x00000200 |
Unicast Connectionless Data Reception. | |
#define | L2CAP_EXTFEA_ECRB_SUPPORTED 0x00000400 |
Unicast Connectionless Data Reception. | |
#define | L2CAP_BLE_EXTFEA_MASK 0 |
Mask for LE supported features used in Information Response (default to none) | |
#define | L2CAP_DEFAULT_ERM_MPS 0x0000 |
Define a value that tells L2CAP to use the default MPS. | |
#define | L2CAP_FCR_OVERHEAD 2 |
Control word. | |
#define | L2CAP_FCS_LEN 2 |
FCS takes 2 bytes. | |
#define | L2CAP_SDU_LEN_OVERHEAD 2 |
SDU length field is 2 bytes. | |
#define | L2CAP_SDU_LEN_OFFSET 2 |
SDU length offset is 2 bytes. | |
#define | L2CAP_EXT_CONTROL_OVERHEAD 4 |
Extended Control Field. | |
#define | L2CAP_MAX_HEADER_FCS (L2CAP_PKT_OVERHEAD + L2CAP_EXT_CONTROL_OVERHEAD + L2CAP_SDU_LEN_OVERHEAD + L2CAP_FCS_LEN) |
length(2), channel(2), control(4), SDU length(2) FCS(2) | |
#define | L2CAP_OFFSET_WO_L2HDR (L2CAP_MINIMUM_OFFSET-(L2CAP_PKT_OVERHEAD+L2CAP_FCR_OVERHEAD)) |
Part of L2CAP_MINIMUM_OFFSET that is not part of L2CAP. | |
#define | L2CAP_FCR_UNSEG_SDU 0x0000 |
Control word to begin with for unsegmented PDU. | |
#define | L2CAP_FCR_START_SDU 0x4000 |
..for Starting PDU of a semented SDU | |
#define | L2CAP_FCR_END_SDU 0x8000 |
..for ending PDU of a segmented SDU | |
#define | L2CAP_FCR_CONT_SDU 0xc000 |
..for continuation PDU of a segmented SDU | |
#define | L2CAP_FCR_SUP_RR 0x0000 |
Supervisory frame - RR. | |
#define | L2CAP_FCR_SUP_REJ 0x0001 |
Supervisory frame - REJ. | |
#define | L2CAP_FCR_SUP_RNR 0x0002 |
Supervisory frame - RNR. | |
#define | L2CAP_FCR_SUP_SREJ 0x0003 |
Supervisory frame - SREJ. | |
#define | L2CAP_FCR_SAR_BITS 0xC000 |
Mask to get the SAR bits from control word. | |
#define | L2CAP_FCR_SAR_BITS_SHIFT 14 |
Bits to shift right to get the SAR bits from ctrl-word. | |
#define | L2CAP_FCR_S_FRAME_BIT 0x0001 |
Mask to check if a PDU is S-frame. | |
#define | L2CAP_FCR_REQ_SEQ_BITS 0x3F00 |
Mask to get the req-seq from control word. | |
#define | L2CAP_FCR_REQ_SEQ_BITS_SHIFT 8 |
Bits to shift right to get the req-seq from ctrl-word. | |
#define | L2CAP_FCR_TX_SEQ_BITS 0x007E |
Mask on get the tx-seq from control word. | |
#define | L2CAP_FCR_TX_SEQ_BITS_SHIFT 1 |
Bits to shift right to get the tx-seq from ctrl-word. | |
#define | L2CAP_FCR_F_BIT 0x0080 |
F-bit in the control word (Sup and I frames) | |
#define | L2CAP_FCR_P_BIT 0x0010 |
P-bit in the control word (Sup frames only) | |
#define | L2CAP_FCR_F_BIT_SHIFT 7 |
#define | L2CAP_FCR_P_BIT_SHIFT 4 |
#define | L2CAP_FCR_SEG_BITS 0xC000 |
Mask to get the segmentation bits from ctrl-word. | |
#define | L2CAP_FCR_SUP_SHIFT 2 |
Bits to shift right to get the S-bits from ctrl-word. | |
#define | L2CAP_FCR_SUP_BITS 0x000C |
Mask to get the supervisory bits from ctrl-word. | |
#define | L2CAP_FCR_INIT_CRC 0 |
Initial state of the CRC register. | |
#define | L2CAP_FCR_SEQ_MODULO 0x3F |
Mask for sequence numbers (range 0 - 63) | |
#define | L2CAP_FCR_TTYPE_CORR_IFRAME 0 |
Corrupt one or more I-frames, based on count. | |
#define | L2CAP_FCR_TTYPE_CORR_SFRAME 1 |
Corrupt an S-frame, (acknowledgement) | |
#define | L2CAP_FCR_TTYPE_STOP_TEST 2 |
Used when turning off a test. | |
#define | L2CAP_FCR_TTYPE_GET_CID 3 |
Returns RFCOMM cid when '0' is passed in cid argument. | |
#define | L2CAP_FCR_FREQ_NORMAL 0 |
A single test is run. | |
#define | L2CAP_FCR_FREQ_RANDOM 1 |
Randomly loses or corrupts a packet. | |
#define | L2CAP_ECRB_MAX_CHANNELS_PER_CMD 5 |
ECRB Max Channels per Command. | |
#define | L2CAP_ECRB_MIN_MTU 64 |
ECRB Min MTU. | |
#define | L2CAP_ECRB_MIN_MPS 64 |
ECRB Min MPS. | |
L2CAP command codes | |
#define | L2CAP_CMD_REJECT 0x01 |
Reject Command. | |
#define | L2CAP_CMD_CONN_REQ 0x02 |
Connection Request Command. | |
#define | L2CAP_CMD_CONN_RSP 0x03 |
Connection Response. | |
#define | L2CAP_CMD_CONFIG_REQ 0x04 |
Configuration Request. | |
#define | L2CAP_CMD_CONFIG_RSP 0x05 |
Configuration Response. | |
#define | L2CAP_CMD_DISC_REQ 0x06 |
Disconnect Request. | |
#define | L2CAP_CMD_DISC_RSP 0x07 |
Disconnect Response. | |
#define | L2CAP_CMD_ECHO_REQ 0x08 |
Echo Request. | |
#define | L2CAP_CMD_ECHO_RSP 0x09 |
Echo Response. | |
#define | L2CAP_CMD_INFO_REQ 0x0A |
Command Information Request. | |
#define | L2CAP_CMD_INFO_RSP 0x0B |
Command Information Response. | |
#define | L2CAP_CMD_AMP_CONN_REQ 0x0C |
AMP Connection Request. | |
#define | L2CAP_CMD_AMP_CONN_RSP 0x0D |
AMP Connection Response. | |
#define | L2CAP_CMD_AMP_MOVE_REQ 0x0E |
AMP Move Request. | |
#define | L2CAP_CMD_AMP_MOVE_RSP 0x0F |
AMP Move Response. | |
#define | L2CAP_CMD_AMP_MOVE_CFM 0x10 |
AMP Move Confirm. | |
#define | L2CAP_CMD_AMP_MOVE_CFM_RSP 0x11 |
AMP Move Confirm Response. | |
#define | L2CAP_CMD_BLE_UPDATE_REQ 0x12 |
LE Connection Param Update Request. | |
#define | L2CAP_CMD_BLE_UPDATE_RSP 0x13 |
LE Connection Param Update Response. | |
#define | L2CAP_CMD_LE_COC_CONN_REQ 0x14 |
LE COC Connection Request. | |
#define | L2CAP_CMD_LE_COC_CONN_RSP 0x15 |
LE COC Connection Response. | |
#define | L2CAP_CMD_CRB_CREDITS 0x16 |
Credits. | |
#define | L2CAP_CMD_ECRB_CONNECT_REQ 0x17 |
Enhanced credit-based connection request. | |
#define | L2CAP_CMD_ECRB_CONNECT_RSP 0x18 |
Enhanced credit-based connection response. | |
#define | L2CAP_CMD_ECRB_RECONFIG_REQ 0x19 |
Enhanced credit-based reconfiguration request. | |
#define | L2CAP_CMD_ECRB_RECONFIG_RSP 0x1A |
Enhanced credit-based reconfiguration response. | |
#define | L2CAP_PKT_OVERHEAD 4 |
Length and CID. | |
#define | L2CAP_CMD_OVERHEAD 4 |
Cmd code, Id and length. | |
#define | L2CAP_CMD_REJECT_LEN 2 |
Reason (data is optional) | |
#define | L2CAP_CONN_REQ_LEN 4 |
PSM and source CID. | |
#define | L2CAP_CONN_RSP_LEN 8 |
Dest CID, source CID, reason, status. | |
#define | L2CAP_CONFIG_REQ_LEN 4 |
Dest CID, flags (data is optional) | |
#define | L2CAP_CONFIG_RSP_LEN 6 |
Dest CID, flags, result,data optional. | |
#define | L2CAP_DISC_REQ_LEN 4 |
Dest CID, source CID. | |
#define | L2CAP_DISC_RSP_LEN 4 |
Dest CID, source CID. | |
#define | L2CAP_ECHO_REQ_LEN 0 |
Data is optional. | |
#define | L2CAP_ECHO_RSP_LEN 0 |
Data is optional. | |
#define | L2CAP_INFO_REQ_LEN 2 |
Info type. | |
#define | L2CAP_INFO_RSP_LEN 4 |
Info type, result (data is optional) | |
#define | L2CAP_BCST_OVERHEAD 2 |
Additional broadcast packet overhead. | |
#define | L2CAP_UCD_OVERHEAD 2 |
Additional connectionless packet overhead. | |
#define | L2CAP_AMP_CONN_REQ_LEN 5 |
PSM, CID, and remote controller ID. | |
#define | L2CAP_AMP_MOVE_REQ_LEN 3 |
CID and remote controller ID. | |
#define | L2CAP_AMP_MOVE_RSP_LEN 4 |
CID and result. | |
#define | L2CAP_AMP_MOVE_CFM_LEN 4 |
CID and result. | |
#define | L2CAP_AMP_MOVE_CFM_RSP_LEN 2 |
CID. | |
#define | L2CAP_CMD_BLE_UPD_REQ_LEN 8 |
Min and max interval, latency, tout. | |
#define | L2CAP_CMD_BLE_UPD_RSP_LEN 2 |
Conn update response length. | |
#define | L2CAP_LE_COC_CONN_REQ_LEN 10 |
LE_PSM, src CID, MTU, MPS, init credits. | |
#define | L2CAP_LE_COC_CONN_RSP_LEN 10 |
Dest CID, MTU, MPS, init credits, result. | |
#define | L2CAP_CRB_CREDITS_LEN 4 |
Local CID, connection credits to add. | |
#define | L2CAP_ECRB_BASE_CONN_REQ_LEN 8 |
LE_PSM, MTU, MPS, init credits. | |
#define | L2CAP_ECRB_BASE_CONN_RSP_LEN 8 |
MTU, MPS, init credits, result. | |
#define | L2CAP_ECRB_BASE_RECONFIG_REQ_LEN 4 |
MTU, MPS. | |
#define | L2CAP_ECRB_RECONFIG_RSP_LEN 2 |
result | |
#define | L2CAP_ECRB_MAX_CONN_REQ_LEN 18 |
LE_PSM, MTU, MPS, init credits + up to 5 CIDs. | |
#define | L2CAP_ECRB_MAX_CONN_RSP_LEN 18 |
MTU, MPS, init credits, result + up to 5 CIDs. | |
#define | L2CAP_ECRB_MAX_RECONFIG_REQ_LEN 14 |
MTU, MPS + up to 5 CIDs. | |
L2CAP Move Channel Response result codes | |
#define | L2CAP_MOVE_OK 0 |
OK. | |
#define | L2CAP_MOVE_PENDING 1 |
Pending. | |
#define | L2CAP_MOVE_CTRL_ID_NOT_SUPPORT 2 |
Control ID Not Supprted. | |
#define | L2CAP_MOVE_SAME_CTRLR_ID 3 |
Same Control ID. | |
#define | L2CAP_MOVE_CONFIG_NOT_SUPPORTED 4 |
Configuration Not Supported. | |
#define | L2CAP_MOVE_CHAN_COLLISION 5 |
Channel Collision. | |
#define | L2CAP_MOVE_NOT_ALLOWED 6 |
Not Allowed. | |
L2CAP Predefined CIDs | |
#define | L2CAP_SIGNALLING_CID 1 |
Signalling CID. | |
#define | L2CAP_CONNECTIONLESS_CID 2 |
Connectionless CID. | |
#define | L2CAP_AMP_CID 3 |
AMP CID. | |
#define | L2CAP_ATT_CID 4 |
Attribute CID. | |
#define | L2CAP_BLE_SIGNALLING_CID 5 |
LE Signalling CID. | |
#define | L2CAP_SMP_CID 6 |
SMP CID. | |
#define | L2CAP_SMP_BR_CID 7 |
SMP BR CID. | |
#define | L2CAP_FIRST_FIXED_CHNL 0x04 |
First fixed channel. | |
#define | L2CAP_LAST_FIXED_CHNL 0x3E |
Last fixed channel. | |
#define | L2CAP_ASSIGNED_NUM_START 0x0020 |
Channel Assigned Number Start. | |
#define | L2CAP_ASSIGNED_NUM_END 0x003E |
Channel Assigned Number End. | |
#define | L2CAP_AMP_TEST_CID 0x003F |
AMP Test CID. | |
#define | L2CAP_BASE_APPL_CID 0x0040 |
Dynamic : Base CID. | |
#define | L2CAP_BLE_CONN_MAX_CID 0x007F |
Max LE CID. | |
Fixed Channels mask bits | |
#define | L2CAP_FIXED_CHNL_SIG_BIT (1 << L2CAP_SIGNALLING_CID) |
Signal Channel Supported (Mandatory) | |
#define | L2CAP_FIXED_CHNL_CNCTLESS_BIT (1 << L2CAP_CONNECTIONLESS_CID) |
Connectionless Reception. | |
#define | L2CAP_FIXED_CHNL_AMP_BIT (1 << L2CAP_AMP_CID) |
AMP Manager Supported. | |
#define | L2CAP_FIXED_CHNL_ATT_BIT (1 << L2CAP_ATT_CID) |
Attribute protocol Supported. | |
#define | L2CAP_FIXED_CHNL_BLE_SIG_BIT (1 << L2CAP_BLE_SIGNALLING_CID) |
LE Signalling Supported. | |
#define | L2CAP_FIXED_CHNL_SMP_BIT (1 << L2CAP_SMP_CID) |
LE Security Manager Supported. | |
#define | L2CAP_FIXED_CHNL_SMP_BR_BIT (1 << L2CAP_SMP_BR_CID) |
Security Manager over BR Supported. | |
L2CAP configuration result codes | |
#define | L2CAP_CFG_OK 0 |
Config OK. | |
#define | L2CAP_CFG_UNACCEPTABLE_PARAMS 1 |
Unacceptable Parameters. | |
#define | L2CAP_CFG_FAILED_NO_REASON 2 |
Failed with No reason. | |
#define | L2CAP_CFG_UNKNOWN_OPTIONS 3 |
Config unknown option. | |
#define | L2CAP_CFG_PENDING 4 |
Config pending. | |
#define | L2CAP_CFG_FLOW_SPEC_REJECTED 5 |
spec rejected | |
L2CAP configuration option types | |
#define | L2CAP_CFG_TYPE_MTU 0x01 |
MTU configuration. | |
#define | L2CAP_CFG_TYPE_FLUSH_TOUT 0x02 |
Flush Timeout configuration. | |
#define | L2CAP_CFG_TYPE_QOS 0x03 |
QOS configuration. | |
#define | L2CAP_CFG_TYPE_FCR 0x04 |
Retransmission & FLow Control configuration. | |
#define | L2CAP_CFG_TYPE_FCS 0x05 |
Frame Check Sequence configuration. | |
#define | L2CAP_CFG_TYPE_EXT_FLOW 0x06 |
Extended Flow Specification configuration. | |
#define | L2CAP_CFG_TYPE_EXT_WIN_SIZE 0x07 |
Extended Windown Size configuration. | |
L2CAP configuration option type lens | |
#define | L2CAP_CFG_MTU_OPTION_LEN 2 |
MTU option length. | |
#define | L2CAP_CFG_FLUSH_OPTION_LEN 2 |
Flush option len. | |
#define | L2CAP_CFG_QOS_OPTION_LEN 22 |
QOS option length. | |
#define | L2CAP_CFG_FCR_OPTION_LEN 9 |
FCR option length. | |
#define | L2CAP_CFG_FCS_OPTION_LEN 1 |
FCR option length. | |
#define | L2CAP_CFG_EXT_FLOW_OPTION_LEN 16 |
Extended Flow Spec. | |
#define | L2CAP_CFG_EXT_WIN_SIZE_LEN 2 |
Ext window size length. | |
#define | L2CAP_CFG_OPTION_OVERHEAD 2 |
Type and length. | |
L2CAP connection result codes | |
#define | L2CAP_CONN_OK 0 |
Connection OK. | |
#define | L2CAP_CONN_PENDING 1 |
Connection Pending. | |
#define | L2CAP_CONN_NO_PSM 2 |
Connection NO PSM. | |
#define | L2CAP_CONN_SECURITY_BLOCK 3 |
Connection Security Block. | |
#define | L2CAP_CONN_NO_RESOURCES 4 |
Connection NO Resource. | |
#define | L2CAP_CONN_BAD_CTLR_ID 5 |
Bad Controller ID. More... | |
#define | L2CAP_BLE_CONN_BAD_AUTHENT 5 |
LE Connection Bad Authentication. | |
#define | L2CAP_BLE_CONN_BAD_AUTHORIZ 6 |
LE Connection Bad Autherization. | |
#define | L2CAP_BLE_CONN_BAD_KEY_SIZE 7 |
LE Connection Bad key size. | |
#define | L2CAP_BLE_CONN_BAD_ENCRYPT 8 |
LE Connection Bad Encryption. | |
L2CAP ECRB Result Code | |
#define | L2CAP_ECRB_ALL_CONNS_SUCCESSFUL 0x0000 |
All Connections Successful. | |
#define | L2CAP_ECRB_ALL_CONNS_REFUSED 0x0002 |
All Connections Refused. | |
#define | L2CAP_ECRB_SOME_CONNS_REFUSED 0x0004 |
Some Connections Refused. | |
#define | L2CAP_ECRB_INSUFF_AUTHENTICATION 0x0005 |
Insufficient Authentication. | |
#define | L2CAP_ECRB_INSUFF_AUTHORIZATION 0x0006 |
Insufficient Autherization. | |
#define | L2CAP_ECRB_INSUFF_KEY_SIZE 0x0007 |
Insufficient Key size. | |
#define | L2CAP_ECRB_INSUFF_ENCRYPTION 0x0008 |
Insufficient Encryption. | |
#define | L2CAP_ECRB_INVALID_SOURCE_CID 0x0009 |
Invalid Source CID. | |
#define | L2CAP_ECRB_SOURCE_CID_IN_USE 0x000A |
Source CID in Used. | |
#define | L2CAP_ECRB_UNACCEPTABLE_PARAMS 0x000B |
Unacceptable Params. | |
#define | L2CAP_ECRB_INVALID_PARAMS 0x000C |
Invalid Params. | |
#define | L2CAP_ECRB_RECONFIG_SUCCESSFUL 0x0000 |
Reconfiguration Successful. | |
#define | L2CAP_ECRB_RECONFIG_FAIL_BAD_MTU 0x0001 |
Reconfiguration fail : Bad MTU. | |
#define | L2CAP_ECRB_RECONFIG_FAIL_BAD_MPS 0x0002 |
Reconfiguration fail : Bad MPS. | |
#define | L2CAP_ECRB_RECONFIG_FAIL_BAD_DCID 0x0003 |
Reconfiguration fail : Bad DCID. | |
#define | L2CAP_ECRB_RECONFIG_FAIL_OTHER 0x0004 |
Reconfiguration fail : Other Reason. | |
#define | L2CAP_ECRB_NOT_SUPPORTED_BY_PEER 0xF000 |
Not Supported by Peer. | |
This file contains L2CAP protocol definitions.
#define L2CAP_CONN_AMP_FAILED 254 |
Connection failed.
#define L2CAP_CONN_CANCEL 256 |
L2CAP connection cancelled.
#define L2CAP_CONN_NO_LINK 255 |
NO Link.
#define L2CAP_CONN_REJECTED 253 |
Connection reject.
#define L2CAP_CONN_TIMEOUT 0xEEEE |
Connection timeout.
#define L2CAP_EXTENDED_FEATURES_INFO_TYPE 0x0002 |
Extended feature Info Type.
Used in Information Req/Response
#define L2CAP_FIXED_CHANNELS_INFO_TYPE 0x0003 |
Fix channel Info Type.
Used in AMP