|
| enum | wiced_bt_rfcomm_port_event_e {
PORT_EV_RXCHAR = 0x00000001,
PORT_EV_RXFLAG = 0x00000002,
PORT_EV_TXEMPTY = 0x00000004,
PORT_EV_CTS = 0x00000008,
PORT_EV_DSR = 0x00000010,
PORT_EV_RLSD = 0x00000020,
PORT_EV_BREAK = 0x00000040,
PORT_EV_ERR = 0x00000080,
PORT_EV_RING = 0x00000100,
PORT_EV_CTSS = 0x00000400,
PORT_EV_DSRS = 0x00000800,
PORT_EV_RLSDS = 0x00001000,
PORT_EV_OVERRUN = 0x00002000,
PORT_EV_TXCHAR = 0x00004000,
PORT_EV_CONNECTED = 0x00000200,
PORT_EV_CONNECT_ERR = 0x00008000,
PORT_EV_FC = 0x00010000,
PORT_EV_FCS = 0x00020000
} |
| | RFCOMM Port Event Masks. More...
|
| |
| enum | wiced_bt_rfcomm_result_e {
WICED_BT_RFCOMM_SUCCESS,
WICED_BT_RFCOMM_ERROR,
WICED_BT_RFCOMM_ALREADY_OPENED,
WICED_BT_RFCOMM_CMD_PENDING,
WICED_BT_RFCOMM_APP_NOT_REGISTERED,
WICED_BT_RFCOMM_NO_MEM,
WICED_BT_RFCOMM_NO_RESOURCES,
WICED_BT_RFCOMM_BAD_BD_ADDR,
WICED_BT_RFCOMM_INVALID_MTU,
WICED_BT_RFCOMM_BAD_HANDLE,
WICED_BT_RFCOMM_NOT_OPENED,
WICED_BT_RFCOMM_LINE_ERR,
WICED_BT_RFCOMM_START_FAILED,
WICED_BT_RFCOMM_PAR_NEG_FAILED,
WICED_BT_RFCOMM_RFCOMM_NEG_FAILED,
WICED_BT_RFCOMM_SEC_FAILED,
WICED_BT_RFCOMM_PEER_CONNECTION_FAILED,
WICED_BT_RFCOMM_PEER_FAILED,
WICED_BT_RFCOMM_PEER_TIMEOUT,
WICED_BT_RFCOMM_CLOSED,
WICED_BT_RFCOMM_TX_FULL,
WICED_BT_RFCOMM_LOCAL_CLOSED,
WICED_BT_RFCOMM_LOCAL_TIMEOUT,
WICED_BT_RFCOMM_TX_QUEUE_DISABLED,
WICED_BT_RFCOMM_PAGE_TIMEOUT,
WICED_BT_RFCOMM_INVALID_SCN
} |
| | RFCOMM Result Codes. More...
|
| |
| enum | wiced_bt_rfcomm_signal_e {
PORT_SET_DTRDSR =0x01,
PORT_CLR_DTRDSR,
PORT_SET_CTSRTS,
PORT_CLR_CTSRTS,
PORT_SET_RI,
PORT_CLR_RI,
PORT_SET_DCD,
PORT_CLR_DCD,
PORT_BREAK
} |
| | RFCOMM Signals. More...
|
| |
|
|
wiced_bt_dev_status_t | wiced_bt_rfcomm_set_buffer_pool (uint16_t buffer_size, uint16_t buffer_count) |
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_create_connection (uint16_t uuid, uint8_t scn, wiced_bool_t is_server, uint16_t mtu, wiced_bt_device_address_t bd_addr, uint16_t *p_handle, wiced_bt_port_mgmt_cback_t *p_mgmt_cb) |
| | Establish serial port connection to the peer device, or allow RFCOMM to accept a connection from peer devices. More...
|
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_remove_connection (uint16_t handle, wiced_bool_t remove_server) |
| | Close the specified connection. More...
|
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_set_event_callback (uint16_t port_handle, wiced_bt_port_event_cback_t *p_port_cb) |
| | Set event callback the specified connection. More...
|
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_set_data_callback (uint16_t port_handle, wiced_bt_rfcomm_data_cback_t *p_cb) |
| | Set event data callback the specified connection. More...
|
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_set_event_mask (uint16_t port_handle, wiced_bt_rfcomm_port_event_t mask) |
| | Set events for which to be notified. More...
|
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_control (uint16_t handle, uint8_t signal) |
| | Send control signal to the peer device. More...
|
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_flow_control (uint16_t handle, wiced_bool_t enable) |
| | This function directs a specified connection to pass flow control message to the peer device. More...
|
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_write_data (uint16_t handle, char *p_data, uint16_t max_len, uint16_t *p_len) |
| | This function sends the given application data to the peer device. More...
|
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_check_connection (UINT16 handle, BD_ADDR bd_addr, UINT16 *p_lcid) |
| | This function checks connection referenced by handle is up and running. More...
|
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_port_get_queue_status (uint16_t handle, wiced_port_status_t *p_status) |
| | This function reports current status of a connection. More...
|
| |
Bluetooth RFCOMM Application Programming Interface.
